Learning how to change tire Getting a flat can be a challenging task for many drivers, but it is a fundamental skill that everyone should have, as it is a relatively common situation that can happen to anyone.
Knowing the correct way to perform this task can save time and money, as well as ensuring your safety on the roads. Therefore, it is very important to master the technique for both cars and motorcycles.
Through our post, you will be able to see the entire step-by-step guide to changing a flat tire, whether on a car or motorcycle, so continue reading to check out all the details on the subject.
How do I change a flat tire on my car?
How to change a tire of a car is a task that all drivers must be prepared to undertake. Here are the basic steps:
Necessary materials
- Monkey;
- Wheel wrench;
- Spare tire;
- work gloves;
- Warning triangle (for safety)
Find a safe location
Before you start changing your tire, make sure you park your car in a safe location away from traffic and on a flat surface. Apply the parking brake and place the warning triangle at an appropriate distance to alert other drivers of your stop.
Prepare the tools
Remove the jack, tire iron and spare tire from the trunk and place them next to the tire that will be replaced to begin the repair process. how to change tire.
Loosen the tire nuts
Using the tire iron, loosen the lug nuts on the tire to be replaced, but do not remove them completely at this time. This must be done while the car is still on the ground to avoid unwanted movement.
Raise the car with the jack
Position the jack under the designated lifting point, usually indicated in the vehicle owner's manual. Pump the jack until the car is high enough that the damaged tire is clearly off the ground.
Remove the lug nuts and damaged tire
Now that the car is in the air, completely remove the lug nuts from the damaged tire. Continuing the process of how to change tire, remove the old tire and set it aside.
Install the new tire
Position the spare tire in place, aligning it correctly with the screws. Then hand-tighten the nuts as much as you can.
Lower the car
Using the jack, carefully lower the car back to the ground until the weight of the vehicle is completely over the new tire.
Tighten the nuts with the wheel wrench
Finally, tighten the nuts with the wheel wrench in a criss-cross sequence, gradually and evenly. This will help ensure the tire is secure. Double check that all nuts are tight.
Store the tools
Store all tools and the damaged tire in the trunk and check that the warning triangle has been replaced. Now you are ready to continue your journey safely and have been able to learn how to change tire.
How to change a motorcycle tire?
How to change a tire Motorbike follows a similar process, but there are some differences to note:
Necessary materials
- Motorcycle stand (optional);
- Wheel wrench or open-end wrench;
- Spare tire;
- work gloves
Find a safe location
Just like in the case of a car, park the motorcycle in a safe place, away from traffic so that you can begin the repair process. how to change tire.
Preparation
Make sure the motorcycle is in neutral and the motorcycle stand is positioned (if available).
Loosen the tire nuts
Using the lug wrench or wrench, loosen the lug nuts on the front or rear tire, depending on the tire being replaced. Do not remove them completely at this time.
Raise the motorcycle (optional)
If you have a motorcycle stand, you can raise the wheel off the ground to make changing the tire easier. Otherwise, the motorcycle may be tilted slightly to the opposite side of the tire to be changed.
Remove the lug nuts and damaged tire
With the lug nuts loosened, remove them completely and remove the damaged tire, which is an important repair step. how to change tire.
Install the new tire
Place the new tire in place, aligning it correctly with the screws. Then hand-tighten the nuts as much as you can.
Tighten the nuts with the wheel wrench or spanner
Using the appropriate tool, tighten the nuts in a criss-cross sequence, gradually and evenly. Make sure all nuts are tight.
Check tire pressure
Make sure the new tire is inflated to the recommended pressure for your motorcycle. This is critical to the safety and performance of the vehicle.
Store the tools
Keep all tools and the damaged tire in a safe place so you can use them at another time, if necessary.
Final thoughts on changing a tire
How to change a tire by car and motorcycling is an essential skill that all drivers and motorcyclists must possess. Remember to practice changing tires in a safe environment before facing an emergency situation on the road.
Also, regularly check your tire pressure and condition to avoid future problems. Road safety largely depends on the proper condition of your vehicle's tires. So be prepared and stay safe.
See also our tips for how to save fuel!